Components ()
View all results.
Categories ()
View all results.
Searching...
Sorry, we couldn't find anything for that search.
Recent Searches.
Return to Captive Screws

Metric Socket Cap Head Captive Screws.

- of components found

No products match the filters selected.

Please clear the filters and try again.
No Results
Metric Socket Cap Head Captive Screws

What are Metric Socket Cap Head Captive Screws?

Metric socket cap head captive screws, also known as captive cap screws or captive socket head cap screws, are metric fasteners from Accu's Captive Screws range that stay attached to a panel, cover or guard when they are undone, so they are not dropped or lost during maintenance. They have the cylindrical head and hexagon socket of a standard socket cap head screw, but the shank directly under the head is narrower than the thread, which runs only on the lower part of the screw. That reduced section lets the screw be retained, either by a push-on captive washer or by a tapped hole in the cover, so the fixing goes wherever the cover goes.

Most of the range is made to DIN 912, the established standard for socket head cap screws, with the reduced shank added for retention, while a smaller set of specialist grades and coatings is made to its manufacturer's own specification. Captive screws are widely used on machinery because the Machinery Directive (2006/42/EC) requires the screws holding a fixed guard to stay attached when the guard is taken off. The same logic applies to enclosures and instruments with covers removed in service.

How Metric Socket Cap Head Captive Screws Work

The reduced section under the head, listed as Captive Diameter (C), is narrower than the thread, so once the threaded end has passed through the cover the screw can slide and turn in its hole without falling back out. On the DIN 912 screws, a push-on captive washer is pressed onto that reduced section behind the cover, trapping the screw while letting it spin freely and lift clear of the frame. The remaining screws rely on the cover itself, which is tapped to match: once the screw has been wound through, its thread catches on the cover's tapped hole whenever it is withdrawn. Either way, the screw clamps the cover to the frame like any cap head screw, but loosening it frees the cover while the fixing stays put.

Consider the rear access guard on a vertical machining centre, held by eight M6 screws and taken off for every coolant pump service and spindle belt change. With ordinary cap screws, each removal puts loose fixings on a machine covered in swarf and coolant, and sooner or later one drops into the chip conveyor and the guard goes back a screw short. Fitted with captive screws instead, the guard comes off as one assembly and is refitted with its full set of fixings. It is properly secured after every service, which is exactly what the Machinery Directive requirement is there to ensure.

Materials Socket Cap Head Captive Screws Are Made From

Accu's range is manufactured from engineering-grade metals, selected to match the strength and corrosion or chemical resistance each application demands:

  • Stainless Steel - (A2): General-purpose austenitic stainless steel for indoor machinery, enclosures and general engineering, from M2 to M12.
  • Stainless Steel - Marine (A4): Molybdenum-bearing stainless steel with greater resistance to chlorides, for marine, outdoor and washdown use, from M3 to M12.
  • Stainless Steel - High Tensile (A2-70): The high-tensile version of A2, rated to property class 70 for a minimum tensile strength of 700 MPa, and the base for the coated options below.
  • Stainless Steel - Marine High Tensile (A4-70): The marine counterpart to A2-70, adding A4’s chloride resistance at the same 700 MPa strength class, from M3 to M8.
  • Stainless Steel - (316L): Low-carbon molybdenum stainless steel for chemical resistance and non-magnetic behaviour, from M3 to M6.
  • Stainless Steel - High Tensile (A2-70) / Stainless Steel - (A2): An A2-70 screw supplied as a set with an A2 retaining washer, adding a second line of retention to the tapped cover hole.
  • Steel - High Tensile (12.9): Property class 12.9 alloy steel with a nominal tensile strength of 1,200 MPa, the strongest grade in the range, protected by electroless nickel plating.
  • Stainless Steel - (303): Free-machining austenitic stainless steel, its added sulphur trading a little of A2’s corrosion resistance for much easier machining, suited to dry indoor enclosures and instrument covers rather than washdown or outdoor guards.

Finishes and pre-applied thread locking add further options:

  • Natural: Uncoated, available on every material except the 12.9 steel.
  • Matte Black: AccuBlack chemical blackening for a non-reflective finish, on A2 and A4.
  • Thread Locking - AccuLock 360: A pre-applied patch that resists loosening under vibration, on A2 from M2 and A4 from M3, up to M12.
  • Thread Locking - Anu-Lok 180: A second pre-applied patch option, on A2 and A4 from M3 to M10.
  • Thread Locking - precote 80: A third patch, matching the A2 and A4 availability of Anu-Lok 180.
  • Fluorine Coating: Reduces the risk of seizing, on A2-70 from M3 to M8.
  • PTFE (Tetrafluoroethylene) Coating: Adds chemical resistance and reduces seizing, across the same A2-70 sizes.
  • Low Temperature Black Chrome: Black and anti-reflective, with added chemical resistance, again on the M3 to M8 A2-70 screws.
  • Electroless Nickel Plating: Corrosion protection for the 12.9 steel, from M3 to M8.

Sizes & Types of Socket Cap Head Captive Screws Available

Accu's range is available in a wide variety of metric sizes and two retention styles:

  • Thread Size: M2 (2 mm) to M12 (12 mm).
  • Thread Pitch: 0.4 mm to 1.75 mm.
  • Length (L): 4 mm to 120 mm.
  • Head Diameter (D): 3.8 mm to 18 mm.
  • Head Length (H): 2 mm to 12 mm.
  • Socket Size (J): 1.5 mm to 10 mm.
  • Captive Diameter (C): 1.4 mm to 9.5 mm.
  • Thread Length (E): 2 mm to 24 mm.
  • Suitable Captive Washer: M3 (3 mm) to M12 (12 mm).
  • Manufacturing Standard: DIN 912 or Not Standardised.

The DIN 912 screws in A2 and A4 are retained with a push-on washer from Accu's Washers For Captive Screws range, matched by the Suitable Captive Washer value, which covers M3 to M12 but not M2, M2.5 or M3.5. The specialist grades are designed to be held by a tapped hole in the cover, but a suitable push-on washer is listed for each of their sizes as well, and the A2-70 sets come with a retaining washer included.

Availability varies by material. A4 starts at M3, so M2 and M2.5 are A2 only, with M2.5 at a single 16 mm length. M12 is limited to Natural, Matte Black and AccuLock 360. Anything longer than 40 mm is A2 or A4, reaching 95 mm at M5 and 120 mm from M6 to M12. The specialist grades and coatings all sit within M3 to M8 and 8 to 40 mm, with 316L stopping at M6. The only 4 mm and 6 mm lengths are the natural A2-70 screws and washer sets, at 4 mm in M3 and 6 mm in M3 and M4.

Fit them with Accu's Metric Hexagon Socket Key Wrenches, which cover every socket size from 1.5 to 10 mm. As an alternative where head height is limited, Low Socket Cap Head Captive Screws offer the same captive function in a lower profile. For covers refitted in awkward positions, Socket Cap Head Captive Dog Point Screws add a guide tip that starts the thread square. Inch-sized assemblies are covered by Imperial Socket Cap Head Captive Screws.

FAQ

Q: Do captive cap screws need a captive washer?

A: It depends on the type. The DIN 912 screws in A2 and A4 take a push-on washer, listed under Suitable Captive Washer from M3 (3 mm) to M12 (12 mm), though M2, M2.5 and M3.5 have no listed washer, so confirm the retention method for those sizes. The specialist grades are retained by a tapped hole in the cover, so a washer is optional on them, although a suitable one is listed for every size and the A2-70 sets include a retaining washer for extra security.

Q: Are captive screws required on machine guards?

A: Often, yes. Section 1.4.2.1 of the Machinery Directive (2006/42/EC) requires the fixings of fixed guards to remain attached to the guard or the machine when it is removed, wherever the guard is likely to come off for cleaning, setting or maintenance. Captive screws are a common way to meet that requirement, though whether a particular guard needs them depends on the machine's own risk assessment, not on the fastener.

Q: What is another name for socket cap head captive screws?

A: They are also called captive cap screws, captive socket head cap screws, captive Allen screws or reduced shank captive screws. All describe a socket cap head screw with a reduced section under the head that lets it be retained in a cover.

Bespoke Metric Socket Cap Head Captive Screws Manufacture.

High precision, bespoke manufacture of Metric Socket Cap Head Captive Screws to customer specification. State of the art facilities specialising in both small batch prototyping and large scale manufacture.

Get A Quote
Metric Socket Cap Head Captive Screws Reviews
4.8
13

Your Browsing History.

Looks Like You're In Looks Like You're Outside

To get accurate pricing, stock, and delivery, please use the Accu site.

We can only deliver within the region you select.

Check Your Region

To get accurate pricing, stock, and delivery, please use the correct Accu Site for your region.